Free Construction Tool

Insulation Calculator – R-Value, Depth & Cost

Reviewed and updated: August 2026

Calculate how much insulation you need to reach your target R-value for attics, walls, floors, and crawl spaces. Supports fiberglass batts, blown-in, rigid foam, and spray foam.

Enter your area dimensions, insulation type, target R-value, and any existing insulation to get depth needed, bags or rolls required, and material cost.

ft
ft
R
$
YOUR RESULTS
Area to insulate
—ft²
R-value needed
—
Bags / rolls needed
—
Material cost
—
Depth needed
—inches

Use this insulation calculator to estimate how much insulation you need to reach your target R-value for attics, walls, floors, and crawl spaces. Enter your area, insulation type, and existing R-value to get depth needed, material quantity, and cost.

Results are planning estimates based on typical coverage rates. Always check the coverage chart on the specific product you purchase, coverage varies by brand, density, and application method.

What R-Value Do I Need?

R-value measures thermal resistance, the higher the number, the better the insulation performs. The US Department of Energy divides the country into eight climate zones and publishes recommended R-values for each. Colder climates require higher R-values to offset greater temperature differentials between inside and outside.

Climate ZoneStates (examples)Attic R-ValueWall R-ValueFloor R-Value
Zone 1 to 2Florida, Hawaii, Texas Gulf CoastR-30 to R-38R-13R-13
Zone 3Georgia, Alabama, California coastR-38R-13 to R-15R-19 to R-25
Zone 4Virginia, Missouri, Oregon, KansasR-38 to R-49R-13 to R-21R-25 to R-30
Zone 5Ohio, Pennsylvania, Colorado, IllinoisR-49R-20 to R-21R-25 to R-30
Zone 6Minnesota, Montana, Vermont, MaineR-49 to R-60R-20 to R-21R-25 to R-30
Zone 7 to 8Alaska, northern MinnesotaR-60+R-21+R-30+

These are DOE recommendations for new construction. For existing homes, adding insulation to meet these targets is one of the most cost-effective energy improvements available. Check your state energy code and local utility rebate programs before starting, many utilities offer incentives for insulation upgrades that can significantly offset material costs.

Insulation Types Compared

Each insulation type has a different R-value per inch, installation method, and best application. Choosing the right type for the location matters as much as choosing the right R-value.

TypeR-Value per InchBest ForDIY FriendlyApprox Cost
Fiberglass battsR-2.9 to R-3.8Open wall cavities, floors, attic floorsYes$0.30 to $0.60 per sq ft
Mineral wool (rock wool) battsR-3.0 to R-3.3Walls, sound control, fire resistanceYes$0.50 to $0.80 per sq ft
Blown-in fiberglassR-2.2 to R-2.7Attic floors, existing wall cavitiesYes (rental blower)$0.25 to $0.50 per sq ft
Blown-in celluloseR-3.2 to R-3.8Attic floors, dense-pack wallsYes (rental blower)$0.25 to $0.50 per sq ft
Rigid foam (EPS)R-3.6 to R-4.2Basement walls, exterior continuous insulationYes$0.25 to $0.50 per sq ft per inch
Rigid foam (XPS)R-5.0Below-grade, exterior, high-moisture areasYes$0.40 to $0.65 per sq ft per inch
Rigid foam (polyiso)R-5.6 to R-6.5Roofing, above-sheathing continuous layersYes$0.50 to $0.80 per sq ft per inch
Open-cell spray foamR-3.5 to R-3.7Interior walls, sound control, air sealingSmall kits only$0.44 to $0.65 per sq ft per inch
Closed-cell spray foamR-6.0 to R-7.0Rim joists, exterior walls, crawl spacesSmall kits only$1.00 to $2.00 per sq ft per inch

How to Calculate Insulation

The basic insulation calculation has two steps: first determine how many inches of depth you need to reach your target R-value, then calculate how many bags, rolls, or boards cover your area at that depth.

Depth needed (inches) = (target R-value - existing R-value) / R-value per inch

For example, adding blown-in fiberglass to reach R-38 in an attic with R-11 existing insulation: (38 - 11) / 2.5 = 10.8 inches of additional blown-in needed.

For bags of blown-in insulation, the coverage per bag varies by product and target depth. The bag label includes a coverage chart showing how many square feet one bag covers at each target R-value. Always use the coverage chart from your specific product rather than a generic estimate, density varies between brands and significantly affects coverage.

Attic Insulation Layers, Visualized

The diagram below shows why layering matters: a second, perpendicular layer of batts covers the thermal bridging that occurs directly over each joist.

CROSS PERPENDICULAR LAYERS TO STOP THERMAL BRIDGING Ceiling joists (existing R-19 batt runs between them) Second layer, laid perpendicular, covers the joists Joist (wood conducts more heat than insulation)

Without the second layer, each joist is a weak point where heat bypasses the insulation between them.

Attic Insulation Guide

Attics are the highest-priority location for insulation upgrades in most homes. Heat rises, and an under-insulated attic floor allows significant heat loss in winter and heat gain in summer. Most unimproved attics have R-11 to R-19 of existing insulation, well below current recommendations of R-38 to R-60 depending on climate zone.

Target R-ValueBlown-in Fiberglass DepthBlown-in Cellulose DepthFiberglass Batts
R-19about 7 to 8 inchesabout 5 to 6 inches6-inch R-19 batt (one layer)
R-30about 11 to 13 inchesabout 8 to 9 inchesR-19 + R-11 (two layers)
R-38about 14 to 17 inchesabout 10 to 12 inchesR-19 + R-19 (two layers)
R-49about 18 to 22 inchesabout 13 to 15 inchesR-19 + R-30 (two layers)
R-60about 22 to 27 inchesabout 16 to 19 inchesR-30 + R-30 (two layers)

When adding a second layer of batt insulation in an attic, lay the new batts perpendicular to the existing ones. This eliminates thermal bridging over the joists, a joist has lower R-value than the insulation between joists, and crossing the second layer over them covers that weak point. Do not use faced batts for the second layer, the facing can trap moisture. Use unfaced batts for all layers except the first.

Never block soffit vents when adding attic insulation. Install baffles (rafter vents) at each rafter bay at the eave before blowing in or laying batts. Blocking soffit ventilation causes moisture buildup and can lead to roof deck rot and mold.

Wall Insulation Guide

Wall insulation is limited by the depth of the framing cavity. A standard 2x4 wall has 3.5 inches of usable cavity depth. A 2x6 wall has 5.5 inches. This limits the maximum R-value achievable with cavity insulation alone.

For walls that need higher R-values than cavity insulation can provide, continuous rigid foam on the exterior is the most effective solution. It also eliminates thermal bridging through the studs, which can reduce the effective R-value of a wall by 15 to 20 percent compared to the cavity R-value alone.

Basement and Crawl Space Insulation

Basement and crawl space insulation strategy depends on whether the space is conditioned (heated and cooled) or unconditioned.

Conditioned Basements

Insulate the foundation walls rather than the floor above. Rigid foam against the concrete wall, covered by drywall or another finish material, is the standard approach. Use XPS or closed-cell spray foam for below-grade applications, these resist moisture better than fiberglass or cellulose.

Unconditioned Basements and Crawl Spaces

Insulate the floor above using fiberglass batts installed between the floor joists with the facing toward the conditioned space above. The floor R-value target is R-25 to R-30 in most climate zones. Batts must be supported, wire insulation hangers or lath strips keep batts from falling over time.

Rim Joists

The rim joist at the top of the foundation wall is one of the most significant air leakage points in a house and is often completely uninsulated. Cutting rigid foam to fit each bay and sealing the edges with canned foam, or applying closed-cell spray foam directly, provides excellent R-value and air sealing in one step. Target R-15 or higher at the rim joist.

Common Insulation Mistakes

Planning Insulation Costs

DIY attic insulation to R-38 typically costs $500 to $1,500 in materials for an average home depending on existing insulation and square footage. Professional blown-in installation runs $1,500 to $4,000. Many utility companies offer rebates of $0.10 to $0.20 per square foot for insulation upgrades, check your local utility's website before purchasing materials.

For total project budgeting, see our project cost estimation guide.

Frequently Asked Questions
How much does it cost to insulate an attic? ▾
DIY blown-in attic insulation to R-38 typically costs $500 to $1,500 in materials for an average home (1,000 to 1,500 sq ft of attic floor). Professional installation runs $1,500 to $4,000 for a standard attic depending on existing insulation, access, and region. Many utility companies offer rebates for insulation upgrades that can offset 10 to 30 percent of the cost, check your local utility's website before purchasing materials.
How many bags of blown-in insulation do I need? ▾
Coverage varies significantly by product, density, and target R-value. A standard bag of blown-in fiberglass insulation covers approximately 40 square feet at R-38 depth, but this varies by brand. Always use the coverage chart printed on the bag for your specific product rather than a generic estimate. Home improvement stores that sell blown-in insulation typically offer free blower rental with a minimum bag purchase, ask at the counter before buying.
Can I add insulation on top of existing insulation? ▾
Yes, for attics, you can add blown-in or unfaced batt insulation directly on top of existing insulation. Lay new batts perpendicular to existing ones to cover thermal bridging over joists. Do not use faced batts for the added layer. For walls, adding insulation to existing finished walls is more complex: it typically requires either drilling and injecting dense-pack cellulose or a full re-insulation project during a renovation. Enter your existing R-value in the calculator to get only the additional insulation needed.
What is the difference between open-cell and closed-cell spray foam? ▾
Open-cell spray foam expands significantly after application, fills cavities well, and provides R-3.5 to R-3.7 per inch. It is vapor-permeable and softer, good for interior walls and sound control but not suitable for below-grade or high-moisture applications. Closed-cell spray foam is denser, provides R-6.0 to R-7.0 per inch, and acts as both an air barrier and a vapor retarder. It is better for rim joists, crawl spaces, and exterior applications where moisture resistance matters. Closed-cell costs roughly twice as much per square foot as open-cell.
Do I need a vapor barrier with insulation? ▾
Whether you need a vapor barrier depends on your climate zone and the location being insulated. In cold climates (zones 5 to 8), a vapor retarder is typically installed on the warm-in-winter side of the insulation in walls, usually the interior face. In mixed and hot climates, vapor retarders are sometimes omitted or placed differently to allow drying. In crawl spaces, a ground cover vapor barrier is almost always required regardless of climate. Consult your local building code, vapor barrier requirements vary by jurisdiction and the wrong placement can cause moisture problems.